The enhanced dewaterability of sludge by a starch-based flocculant combined with attapulgite | Scientific Reports

2023-01-11 00:34:23 By : Ms. Ivy Zhuang

Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Scientific Reports volume  13, Article number: 402 (2023 ) Cite this article Acrylamide Polymerization

The enhanced dewaterability of sludge by a starch-based flocculant combined with attapulgite | Scientific Reports

Coagulation/flocculation is one of the most widely used and cost-effective pretreatment methods for improving the dewaterability of sludge. In this study, a cationic modified starch-based flocculant (St-CTA) in conjunction with a popular clay, attapulgite (ATP), was used for the conditioning of waste-activated sludge. The dewatering properties, including the filter cake moisture content, filtration specific resistance, capillary suction time, filtration rate and compressibility coefficient, were measured and compared by varying the doses of St-CTA and ATP. By combination of the apparent dewatering performance and the changes in the contents and distributions of the extracellular polymeric substance (EPS) fractions and components, sludge flocs, and microstructures of sludge cakes, the dewatering mechanisms were discussed in detail. St-CTA in conjunction with ATP can exhibit an enhanced dewaterability of sludge and the water content in final sludge cake can be stably reduced below 80% owing to the synergistic effects of St-CTA and ATP. In addition to the efficient charge neutralization of St-CTA, ATP not only acts as a skeleton builder in the sludge dewatering process which makes the sludge flocs more compact and improves the filterability and permeability, but also tightly interacts with the proteins in EPS of the sludge which reduces the protein content and further enhances the dewatering effect. This study provides an economical, green, and effective way to further improve the dewaterability of sludge.

In recent years, with the steady improvement of the world economy, the scale of water and wastewater treatment have notably increased, and accordingly the discharge of sludge as a by-product of wastewater treatment has consistent growth1. However, raw sludge usually contains more than 95% water2, the high volume of which causes its high transport and disposal costs3. It is therefore vitally important to reduce the volume of sludge by the dewatering processes for its efficient treatment4.

Sludge is usually conditioned by some pre-treatments before the mechanical squeezing to efficiently separate water from the sludge5. Sludge pre-treatments, mainly including coagulation/flocculation, oxidation, acidification, skeleton building, microwave and ultrasonic conditioning, can convert the surface adsorbed water and internal hydrated water into free water, in which coagulation/flocculation is a widely used one in the wastewater treatment plants because of its simplicity and effectiveness6. Traditional coagulants and flocculants, such as polyaluminium chloride, polyferric sulfate and cationic polyacrylamide (PAM), were widely used because they can effectively aggregate the sludge particles and achieve the solid–liquid separation6. However, the residual metal ions and highly toxic monomers of these traditional coagulants and flocculants may cause the potential environmental risks7. Moreover, the traditional coagulation/flocculation is difficult to achieve a complete dewatering because the highly hydrated organic matters in sludge such as the extracellular polymeric substance (EPS), binding large amounts of water, were difficult to be destroyed to fully release the bound and intracellular water8,9. Besides, highly compressible sludge cakes would compact fully under the high mechanical pressure, causing the drainage channels destroyed, the filterability reduced and the internal bound water prevented from being completely drained6,10,11. Therefore, coagulation/flocculation used solo is difficult to meet the high requirements of sludge dewatering, and an environmentally-friendly and effective combined conditioning processes with other pre-treatments can notably improve the dewaterability of sludge1,6,12,13.

Commonly combined conditioning processes included acidification-coagulation12, oxidation-coagulation13, and coagulation and skeleton builder combination process1. Among them, acidification-coagulation and oxidation-coagulation can effectively destroy the EPS and release the intracellular water but cannot enhance the filterability of sludge cakes14. The coagulation and skeleton builder combination process is based on the coagulation and the addition of some skeleton builders, as filter aids, to condition the sludge5. Some skeleton builders, such as bentonite, fly ash and biomass ash, are widely available and inexpensive, besides, contain high levels of SiO2 with a good mechanical strength4,15,16,17. With the support of the skeleton builders, the sludge cake contains rigid and porous microstructure even under a high mechanical pressure, reducing the compressibility of sludge, allowing the water contained in the sludge cakes to drain out easily, and thus improving the permeability and mechanical strength of sludge to achieve a high solid content in sludge (> 30% dry sludge volume)4,15,16,17. The coagulation and skeleton builder combination process thus has the advantages of high-cost performance and ease of operation by the direct addition of flocculants and skeleton builders without any adjustment6,7; besides, the porous and rigid structures of the skeleton builders can easily change the sludge compressibility and further enhance the sludge dewatering performance by this combining process.

Starch is one of the environmentally-friendly and low-cost polysaccharides18. In this work, an etherified cationic starch-based flocculant with a high charge density, namely starch-3-chloro-2-hydroxypropyltrimethylammonium chloride (St-CTA), was synthesized19, on which the quaternary ammonium cationic groups can also effectively damage the cellular structures and interact with EPS. St-CTA has thus shown a notable effect on sludge dewatering according to previous reports13,19. Besides, some clays, such as montmorillonite and kaolin, have been confirmed as efficient skeleton builders in combination with various flocculants for effective conditioning of sludge17,20. Attapulgite (ATP), a popular clay in China, has the characteristics of the high specific surface area, the rigid and porous structure and good adsorption properties to many organic matters21,22. ATP, as a skeleton builder, was thus in conjunction with St-CTA here. The dewatering performance of their combined usages for waste-activated sludge with different dosing sequences and various dosing ratios was assessed in terms of specific resistance of filtration (SRF), filter cake moisture content (FCMC), time to filter (TTF), floc properties and microstructures of sludge cakes. Changes in the EPS distribution and composition of the conditioned sludge were investigated relative to the final dewatering efficiency. The synergistic mechanisms of St-CTA and ATP were also discussed in detail. This work thus proposes a novel economical combination conditioning method for sludge dewatering.

Before the dewatering experiment, the effects of three different dosing sequences using grinded or not grinded ATP on the sludge dewatering, i.e. ATP dosed before, together, or after St-CTA, were studied and compared firstly, as shown in Supporting Information Figs. S1, S2. According to Fig. S1, the FCMC and SRF of sludge after conditioned by this combination had no evident differences under the three different dosing sequences. However, St-CTA dosed before ATP showed slightly better dewatering performance with increasing ATP dose, by which the optimal FCMC and SRF were around 79.50% and 0.30 × 1012 m/kg, respectively, at the ATP dose approximately 10.00 kg/m3 (Fig. S1e–f). This finding might be due to that the ATP could easily combine with the primary sludge flocs formed by the previously fed St-CTA to improve the filterability and permeability of the final sludge cakes. Similarly, Supporting Information Fig. S2 shows no notable change in the FCMC and SRF of sludge by using grinded or not grinded ATP with the average particles size approximately 8.577 μm and 18.107 μm respectively (Fig. S2g). However, a slight better dewatering performance were obtained using not grinded ATP when the ATP dose increased to 10.00 kg/m3 (Fig. S2e–f). Accordingly, the conditioning process of unground ATP fed after St-CTA was highly efficient and convenient, which was thus applied in the following dewatering experiments.

The various conditioning processes with different doses of St-CTA and ATP, named CS-ATP1—CS-ATP19, were conducted to sludge and their dewatering performance are shown in Figs. 1,2, Table 1, and Supporting Information Figs. S3–S5. According to Figs. 1,2, Table 1, and Supporting Information Figs. S3–S5, the dewatering performance of sludge conditioned with St-CTA individually evidently improved especially at the low dose range but reached a plateau when St-CTA was dosed at the optimal dose of 16.00 mg/gTSS or even deteriorated after the optimal doses, specifically, the FCMC reduced from 97.86 to 82.52%, SRF was from 4.10 × 1012 to 0.57 × 1012 m/kg, CST was from 50.6 to 10.1 s, TTF was from 320 to 53 s, the compressibility coefficients was from 1.26 to 1.02, the filtrate volume was from 32.1 to 95.0 mL and the filtration rate was from 0.2546 to 1.4218 m3/(m2 h) at the optimal dose. This finding confirmed that the charge naturalization of St-CTA was crucial to the sludge conditioning process and the excessive positive charges might lead to the restabilization of sludge colloidal dispersions (CS-ATP5, CS-ATP10 and CS-ATP15, Fig. 3)6,23,24. Besides, St-CTA, a polysaccharide-based material with a rigid chain structure, could still act as a skeletal builder to build drainage channels, which was conducive to water run-off and thus improving the sludge dewatering6. Based on Figs. 1,2, Table 1, and Supporting Information Figs. S3–S5, the dewatering performance of sludge conditioned with St-CTA in conjunction with various constant doses of ATP was all improved and showed similar patterns to that with only St-CTA because of the synergistic effects of St-CTA and ATP.

The sludge dewatering performance of St-CTA in conjunction with ATP by using different doses: (a) FCMC, (b) SRF, (c) CST and (d) TTF.

The compressibility coefficients of sludge conditioned by St-CTA in conjunction with ATP using different doses.

The zeta potentials of the sludge supernatants conditioned by St-CTA in conjunction with ATP using different doses.

Figures 1,2, Table 1, and Supporting Information Figs. S3–S5 show that the conditioning effect of ATP used only was quite limited (CS-ATP1–CS-ATP4) owing to ATP with a negatively surface charge (Fig. 3), which was consistent with the previous reports1,4. However, ATP dosed after St-CTA could further improve the dewatering performance of St-CTA, specifically, the FCMC reduced from 82.52 to 76.99% and the compressibility coefficients was from 1.02 to 0.79 conditioned by 16.00 mg/g TSS of St-CTA in conjunction with an optimal ATP dose of 14.00 kg/m3 (CS-ATP14, Fig. 1, Table 1). When the ATP dose increased further, the improvement in dewatering performance was quite limited (Supporting Information Fig. S6) but the resultant sludge mass was accordingly constantly increased. In addition, ATP dosed after St-CTA could also obviously alleviate the restabilization effect6,23,24. When St-CTA was overdosed at the dose of 26.67 mg/gTSS, the FCMC improved from 88.88 to 76.71% at the ATP dose of 14.00 kg/m3 (CS-ATP19, Fig. 1 and Table 1). The negatively surface charged solid particulates of ATP could act as a skeleton builder to reduce the compressibility of sludge and further improve the FCMC (Figs. 1a, 2), besides, could neutralize and combine the excessive positive charges of overdosed St-CTA and thus weaken the restabilization effect6,23,24 (CS-ATP15, CS-ATP17 and CS-ATP 19, Fig. 3). The formed composites of St-CTA and ATP may cause the flocs rough and compact (Supporting Information Fig. S7) due to the dense structure of ATP25. However, ATP had less improvement in some dewatering performance especially for CST after combination of St-CTA (Fig. 1c) possibly due to the error in the determination of the filtration volume and CST26 caused by decreased filtration time and the sludge cake broken quickly in the promoted dewatering processes after the addition of ATP.

In addition, the dewatering performance of this combination has been compared with a commercial flocculant, PAM, currently used in the wastewater treatment plant in Nanjing (Supporting Information Fig. S8). According to Fig. S8, the optimal FCMC obtained by PAM was 84.81% and was much higher than that by the combined conditioning method in this work approximately 76.99% (CS-ATP14, Fig. 1 and Table 1), although PAM had a lower optimal dose of 5.33 mg/gTSS. Fig. S8 still indicates that St-CTA in conjunction with ATP showed a wider effective dewatering window approximately 5.00–26.00 mg/g TSS than PAM about 3.00–8.00 mg/g TSS. Table 2 further compared their cost. Accordingly, the cost of the optimal conditioning process (CS-ATP14) was only 14.55 USD/tTSS, which was lower than PAM about 21.32 USD/tTSS in water plants. In addition to PAM, the dewatering performance of this combination has been roughly compared with some traditional coagulants also, such as FeCl3, polyaluminium chloride (PAC), and CaO, according to previous reports19,27,28. The optimal FCMC of sludge conditioned by FeCl3 or PAC alone was about 84%19,27, which was notably higher that by this combination. CaO had a good dewatering effect, but the resultant pH of the conditioned sludge was higher and the subsequent treatment was thus complicated28.

In short, St-CTA followed by the addition of ATP exhibited better and more stable dewatering performance because of the charge neutralization and bridging effects of St-CTA in conjunction of the skeleton builder effect of ATP, and the optimal doses of St-CTA and ATP were obtained about 16.00 mg/gTSS and 14.00 kg/m3, respectively.

The sizes and D2s of sludge flocs conditioned with different doses of St-CTA and ATP are shown in Fig. 4 based on the image analysis7,29 (Fig. 5 and Supporting Information Fig. S9). Figure 4 shows that the sizes and D2s of sludge flocs increased with the increase of the dose of St-CTA at the beginning but then decreased after reaching the maximal values at 16.00 mg St-CTA/g TSS, even in conjunction with ATP, due to the restabilization effect6,23,24, which was fully consistence with the dewatering performance (Figs. 1,2, Table 1, and Supporting Information Figs. S3–S5). In addition, the addition of St-CTA made the surface of sludge flocs turn from relatively smooth to rough and porous due to the efficient coagulation effect of St-CTA (Fig. 6c), which facilitated the aggregation and compression in the following mechanical dewatering to further remove the water from the sludge. Furthermore, the addition of ATP caused much more small solid particles embedded in the sludge flocs (Fig. 6b,d), as skeleton builders, to possibly create drainage channels in the subsequently formed sludge cakes and further improve the sludge dewatering performance30.

The properties of sludge flocs produced by St-CTA in conjunction with ATP using different doses: (a) Average floc size (l) and (b) 2D fractal dimension (D2).

Optical microscope images of sludge flocs: (a) raw sludge and conditioned by (b) ATP, (c) St-CTA, and (d) St-CTA in conjunction with ATP at respective optimal dose, that is, St-CTA is 16.00 mg/gTSS and ATP is 14.00 kg/m3.

SEM images of sludge flocs: (a) raw sludge and conditioned by (b) ATP, (c) St-CTA, and (d) St-CTA in conjunction with ATP at respective optimal dose, that is, St-CTA is 16.00 mg/gTSS and ATP is 14.00 kg/m3.

However, the sizes and D2s of sludge flocs had a contrary change trend with the increase of ATP doses after combined with St-CTA (Fig. 4). The addition of ATP made floc size smaller was possibly due to two facts. One was that the primary sludge flocs would be broken up by the second rapid mixing in the conditioning of ATP after St-CTA; The other was that some of ATP was not combined with the sludge flocs, and the employed ATP has an average particle size of approximately 18.107 μm, much smaller than the primary sludge flocs, which caused the obtained apparent average sludge flocs size turned smaller (Fig. 4). However, the denser structure of ATP was resultant in more compact internal structures of sludge flocs and higher detected D2s31. Consistently, the addition of ATP after St-CTA could benefit to the improvement of the dewatering performance (Figs. 1,2, Table 1, and Supporting Information Figs. S3–S5), which implicated that the relatively small but compact sludge flocs caused a good dewatering property (Fig. 4).

The sludge flocs were further aggregated, compressed and formed into sludge cakes under the following mechanical squeezing. Figure 7 compares the surface morphologies of sludge cakes obtained without and with conditioning under various treatments. The surface of the sludge cake without conditioning was relatively smooth, flat and lacking micropores (Fig. 7a). After conditioning by St-CTA, ATP and their combination, respectively, the surfaces of the sludge cakes all became rough and microporous, among which this change in surface morphology of sludge cake treated by the combination of St-CTA and ATP was more evidently (Fig. 7b–d). This voids and porous structure could create drainage channels in sludge cakes and improve the filterability and permeability, which was beneficial to further discharge the internal water from the sludge30,32. The observed surface morphologies of sludge cakes were fully consistent with their corresponding sludge floc properties (Fig. 4), compression coefficients (Fig. 2 and Supporting Information Fig. S5 and dewatering performance (Fig. 1, Table 1, and Supporting Information Figs. S3–S4). St-CTA can efficiently coagulate and aggregate the sludge mainly by charge neutralization, and also partial St-CTA and ATP acted as skeleton builders can reduce the compressibility of the sludge cakes. Moreover, the superior dewatering performance of the combination of St-CTA and ATP was ascribed to their synergistic effects.

SEM images of sludge cakes: (a) raw sludge and conditioned by (b) ATP, (c) St-CTA, and (d) St-CTA in conjunction with ATP at respective optimal dose, that is, St-CTA is 16.00 mg/gTSS and ATP is 14.00 kg/m3.

According to numerous reports in the literature33,34, EPS is one of the main factors affecting the sludge dewatering efficiency, but the effect of ATP on EPS has not been systematically studied. The effects of ATP on the EPS fractions and components were investigated (Fig. 8). As to the sludge conditioned by ATP only (CS-ATP2 and CS-ATP4) and St-CTA individually (CS-ATP10 and CS-ATP15), respectively, the TOC contents in three EPS factions (S-, LB- and TB-EPS) were almost declined (Fig. 8a). These findings indicated that St-CTA and ATP could both inhibit the EPS. The S-EPS would aggregate and settle down while part of LB-EPS would be converted into TB-EPS owing to the charge neutralization and bridging flocculation effects of St-CTA19 and the possible interactions of ATP, such as the chelation effect between the metal ions on ATP and those organic matters35,36, which would be discussed in detail in the following section. However, the further decreased contents of TB-EPS might be due to that they were bound to the sludge particles too tightly to detect under currently used measured methods7,37,38,39. Besides, the TOC contents in EPS were thus continuously decreased with the dose of ATP due to their enhanced interactions (CS-ATP2/CS-ATP4, CS-ATP10/CS-ATP12/CS-ATP14, and CS-ATP15/CS-ATP17/CS-ATP19). However, the TOC contents in three EPS factions had slightly increased due to the restabilization effect19,23,24 , when St-CTA was overdosed (CS-ATP15).

The contents of different EPS components in sludge conditioned by St-CTA in conjunction with ATP using different doses: (a) TOC, (b) protein (PN) and (c) polysaccharides (PS).

Moreover, St-CTA in conjunction with ATP caused the TOC contents in those three EPS factions decreased further because of their synergistic effect, confirming the superior dewatering effect of this combined technique (Fig. 8a). The optimal process, i.e. CS-ATP14, was accordingly obtained, in which the doses of ATP and St-CTA were 14.00 kg/m3 and 16.00 mg/g TSS, respectively. The changes in TOC contents in EPS with the doses of St-CTA and ATP were fully matched to the sludge dewatering performance (Figs. 1,2, Table 1, and Supporting Information Figs. S3–S5). The decrease in the EPS contents was confirmed to be beneficial to improvement of the dewaterability of sludge33,34.

The chemical compositions of EPS mainly include PN, PS, humic acid, fulvic acid, and nucleic acid, in which PN and PS are two important ones40. The contents of PN and PS in different EPS fractions of the sludge conditioned by different CS-ATP processes were further determined in Fig. 8b,c. Figure 8b,c show that the change trends in the contents of PN and PS were almost similar to those of TOC in three EPS fractions with the doses of St-CTA and ATP (Fig. 8a). Differently, the contents of PN in all three EPS fractions decreased evidently but those of PS was changed insignificantly to one another after the addition of ATP in the both presence and absence of St-CTA (CS-ATP2/CS-ATP4, CS-ATP10/CS-ATP12/CS-ATP14, and CS-ATP15/CS-ATP17/CS-ATP19). This finding indicated that ATP mainly acted on the PN rather than PS, because the metal irons on ATP, such as Al3+ and Fe3+ which initially bind to the negatively surface charged ATP, would readily chelate with the –NH2 and –COOH of PN, resulting in the further aggregation and precipitation of PN35,36. Moreover, PN in S-EPS was substantially inhibited in the optimal process, i.e. CS-ATP14, confirming the efficient synergistic effects of St-CTA and ATP.

Besides, the strong Pearson correlations between PN, PS and TOC contents of different EPS fractions and the FCMC and SRF of sludge as shown in Table 3 also indicated the PN, PS and TOC contents in EPS were closely related to the sludge dewatering performance41. In short, St-CTA in conjunction with ATP could efficiently inhibit the EPS and thus effectively improve the dewaterability of sludge.

As mentioned earlier, the EPS still contains many other organic substances in addition to PN and PS. The 3D-EEM spectra of different EPS fractions in sludge before and after conditioned by St-CTA and ATP with different doses were also measured (Supporting Information Figs. S10, S11). According to previous literature42,43, the 3D-EEM spectrum can be mainly divided into five regions representing different substances, mainly aromatic PN (λex/em = 230/340 nm, Peak A), tryptophan-like PN (λex/em = 280/350 nm, Peak B), fulvic acid (λex/em = 240/420 nm, Peak C) and humic acid substances (λex/em = 350/440 nm and 270/450 nm, Peaks D and E). Accordingly, Fig. 6 and Supporting Information Table S1 show the summary of the intensities of these five characteristic peaks in different EPS fractions.

According to Fig. 9 and Supporting Information Table S1, the changes trends in the intensities of these five characteristic peaks in different EPS fractions with the doses of St-CTA and ATP were apparently similar to those in the TOC of the three EPS fractions (Fig. 8a). More detailly, the Pearson correlations between the intensities of the various fluorescent signals and the sludge dewaterability were shown in Table 3. Table 3 indicates that the protein-like substances including aromatic PN (Peak A) and tryptophan-like PN (Peak B) are both strongly related to the sludge dewatering performance in all three EPS fractions; however, the fulvic acid (Peak C) and humic acid substances (Peaks D and E) are closely associated with the sludge dewatering performance only in S-EPS. Combination of the correlation analysis of the TOC, PS and PN contents in Table 3, S-EPS is closely related to sludge dewatering performance19 and the PN in EPS rather than humic acid and fulvic acid has dominant effect44,45,46.

The intensities of various 3D-EEM characteristic peaks of (a) S-EPS, (b) LB-EPS and (c) TB-EPS in sludge conditioned by St-CTA in conjunction with ATP using different doses.

According to the aforementioned discussion, the sludge dewatering mechanisms were schematically described in Fig. 10. The negatively surface charged sludge particles combined with EPS were initially small and dispersed, in which contained a large amount of water. When the positively charged St-CTA was dosed, St-CTA would agglomerate the sludge particles and also efficiently inhibit the EPS together through charge neutralization and bridging flocculation effects. The following addition of ATP not only acted as a skeleton builder in the agglomerated sludge cakes to enhance the permeability and filterability of sludge but also effectively chelate with the highly hydrophilic PN substances in the EPS of the sludge through the metal ions on ATP, thereby together improvement of the dewaterability of the sludge38,40,47.

Schematic diagram of the mechanisms in sludge dewatering by the combination of St-CTA and ATP.

In addition to the aforementioned synergistic effects of St-CTA and ATP causing an efficient performance in sludge dewatering, the precursor of St-CTA, i.e. starch, and ATP are both natural materials with the evident features of environmental-friendliness, wide source and low cost. The combination of St-CTA and ATP thus had a high cost performance in sludge dewatering. However, there still exists some disadvantages and challenges in this combined conditioning method in the future application. The addition of ATP would inevitably increase the resultant total mass of sludge and thus increase the difficulty of the subsequent treatment. Besides, St-CTA and ATP could not substantially destroy the EPS in sludge and fully release the bound water, which caused to difficultly improve the sludge dewatering performance further. To reduce the dose of skeleton builder and the resultant sludge mass, high-performance flocculants should be developed, which are intrinsically based on the well-established structure–activity relationship6,7. Dewatering mechanisms should be thus studied in detail on the basis of the structural characteristics of flocculants and also the key components in sludge, such as the secondary structure of protein in EPS48. Besides, the pre-oxidation method may completely destroy the EPS in sludge13, and thus the combination process with pre-oxidation was feasible to further improve the sludge dewatering performance.

This study mainly focused on the usage of a cationic etherified modified starch-based flocculant, St-CTA, followed by a clay material, ATP, to condition the sludge and improve the sludge dewatering; and the synergistic dewatering mechanisms were investigated in detail. The main results obtained were summarized as follows:

(1) It demonstrated that ATP fed after St-CTA shows slightly higher efficiency in sludge dewatering than the other two dosing sequences. Specifically, the sludge conditioning process by 16.00 mg/g TSS of St-CTA in conjunction with 14.00 kg/m3 of ATP has a superior sludge dewatering performance and a low cost of approximately 14.55 USD/tTSS, besides, the FCMC was accordingly reduced from 97.86 to 76.99% and the sludge flocs were compacted with a D2 of approximately 1.933. The utilization of this combined conditioning process for sludge dewatering thus has a promising application potential.

(2) On the basis of the analysis of the changes in the contents and distributions of the EPS fractions and components in the sludge conditioned by St-CTA and ATP with different doses associated with the Pearson correlation analysis, St-CTA and ATP could both inhibit the EPS, and S-EPS is closely related to sludge dewatering performance. Besides, the combination of St-CTA and ATP efficiently reduced the PN in all three EPS fractions totally from 6.09 to 3.01 mg/gTSS, which all exhibited significant correlations (p < 0.05) with the dewatering parameters of SRF and FCMC, and PN in EPS rather than humic acid and fulvic acid thus has a dominant effect in sludge dewatering.

(3) The superior sludge dewatering performance of this combined process by St-CTA and ATP was ascribed to their synergistic effects. The positively charged St-CTA could efficiently aggregate and coagulate the sludge particles and also efficiently inhibit the EPS together through charge neutralization and bridging flocculation effects. The following addition of ATP not only acted as a skeleton builder in the agglomerated sludge cakes to enhance its permeability and filterability, causing the compression coefficient of the sludge cakes reduced from 1.26 to 0.79, but also effectively chelate with the highly hydrophilic PN substances in the EPS of the sludge through the metal ions on ATP, thereby together improvement of the dewaterability of the sludge.

Starch (St, weight-average molecular weight ~ 1.5 × 105 g/mol) was obtained from Binzhou Jinhui Corn Development Co., Ltd. 3-chloro-2-hydroxypropyltrimethylamm-onium chloride (CTA, 60wt% in water) was purchased from Aladdin Industrial Corporation. St-CTA with a St to CTA feeding mass ratio of 1:1.5 was synthesized, of which charge density was determined approximately 1.875 mmol/g by colloidal titration29,49. ATP was purchased from MESB (Meishibo), Changzhou, with an average particle size [d(0.5)] of approximately 18.107 μm obtained by a laser diffraction particle size analyzer (Mastersizer 2000, Malvern, UK). ATP was fully dried in an oven before use, the zeta potential of which was determined to be approximately -9.08 ± 0.09 mV. PAM (weight-average molecular weight of approximately 1.0 × 107 g/mol and CD of 1.06 ± 0.13 mmol/g), was obtained from Dongying Nuoer Chemical Co., Ltd.

Waste-activated sludge samples were taken from a wastewater treatment plant at Nanjing, which treats sludge by the activated sludge process and membrane bioreactors. The samples were stored in a refrigerator at 4 °C and the same series of experiments by using the same sludge were completed within 7 days. All the physicochemical properties of the sludge including their detailed determination methods are shown in Supporting Information Table S2.

The 250-mL jars were performed for the conditioning of 100 mL sludge suspension through a six-place programmed paddle mixer model of TA6 (Wuhan Hengling Tech. Co. Ltd.) at room temperature. The detailed conditioning process was as follows. Various volumes of the freshly prepared St-CTA solution (4.0 g/L) was added to the sludge suspensions; the mixture was stirred quickly at 250 rpm for 1.0 min, followed by a slow stirring at 50 rpm for 2.0 min; and then different amounts of ATP were added into the sludge mixtures, which were stirred quickly at 250 rpm for 30 s and then a slow stirring at 50 rpm for 3.5 min. The conditioned sludge was used for subsequent experiments to determine the FCMC, SRF, capillary suction time (CST), compression coefficient, floc properties including floc size and compactness, zeta potentials, and the fractions and components of EPS extractions. The aforementioned characterization methods are described in detail in Supporting Information Table S2. Each experiment was measured in triplicate, and the final results represented the values average with the relative error less than 5%.

FCMC and SRF are two important parameters for evaluating the sludge dewatering performance, where SRF is the determination of sludge specific resistance by pumping the conditioned sludge through a 0.05 MPa pressure Brinell funnel. The extracted filtrate was collected in a 100 mL measuring cylinder, and the cylinder reading was recorded every 5 s from the start of pumping until the sludge cake broke or until it reached 6.0 min. The sludge cake was dried in an oven at 105 °C and the FCMC was determined according to previous report50. The SRF of the sludge was calculated as follows7,49:

where P (N/m2) represents the pressure used for filtration, Sa (m2) shows the area of the filter paper used for extraction, b (s/m6) indicates the slope of filtrate discharge curve; μ is the kinetic viscosity and ω indicates the dry weight per unit volume of sludge on the filtrate medium.

CST was measured by using a CST apparatus (England Triton Electronics 304 m) to indicate the filterability of free water in sludge51. The sludge compression performance is expressed by the sludge compression coefficient (s), which is obtained by measuring the sludge specific resistances under different pumping pressures, i.e. 0.02, 0.03, 0.04 and 0.05 MPa according to Eq. (2)47,52:

TTF refers to the time required to obtain a filtrate volume equal to the half volume of sludge under the pressure of 0.05 MPa5,53. The filtration volume refers to the volume of filtrate in the measuring cylinder at the end of the filtration. The filtrate rate (q), which indicates the rate of filtration, is determined by Darcy’s law according to Eq. (3):

where V is a filtrate volume (m3) which is read from the measuring cylinder at the end of filtration, Sb is a filtration area (m2) and t is filtration time (h)53.

The floc properties of the treated sludge including the floc size (l) and the two-dimensional fractal dimension (D2) were determined to study the microstructural changes in the conditioned sludge. The sludge flocs were photographed with a Pentax Model K-m digital camera equipped with an optical microscope (XTL-3400; Shanghai Caikon Optical Instrument Co., Ltd.) under a fixed magnification. l was the characteristic length of sludge floc and the longest line joining two points of object’s outline and passing through the centroid. As mentioned in the previous study7,29, the projected characteristic length l and the projected area (A) of the sludge floc were measured by means of an image analysis software (Image pro® Plus 6.0), and D2 was accordingly obtained by the logarithmic fitting of Eq. (4).

The conditioned sludge flocs and their sludge cakes formed after a following mechanical squeezing were freeze-dried at − 60 °C for 72 h and then their surface morphologies were directly observed using a scanning electron microscopy (SEM, FEI Quanta 250).

The EPS in sludge was mainly classified into soluble EPS (S-EPS), loosely bound EPS (LB-EPS) and tightly bound EPS (TB-EPS)6, which are extracted by a modified ultrasonic thermal extraction method in this work7,54. Details of operation method are as follows: 10 mL of the sludge was centrifuged in a tube at 3000 rpm for 10.0 min, the supernatant was extracted and filtered through a 0.45 μm filter membrane to obtain S-EPS. The remaining sludge was resuspended to 10 mL with 0.05% mass fraction NaCl solution, sonicated at 20 kHz for 2.0 min and then shaken in a shaker at 150 rpm for 10.0 min, followed by centrifugation at 5000 rpm for 10.0 min, the supernatant was extracted and filtered through a 0.45 μm membrane to obtain LB-EPS. The remaining sludge was resuspended in 0.05% mass fraction NaCl solution to 10 mL, sonicated at 20 kHz for 3.0 min, heated in a water bath at 60 °C for 30.0 min, and then centrifuged at 8000 rpm for 10.0 min to extract the supernatant and filtered through a 0.45 μm membrane to obtain TB-EPS.

Total organic carbon (TOC) in EPS fractions was measured by a total organic carbon analyzer (Aurora 1030 W, USA) to indicate dissolved organic matters in the sludge. Protein (PN) contents were measured using a UV-2600A spectrometer (Unico USA) with bovine serum albumin (BSA) as the standard substance55,56. The three extracts of EPS and the standard solution of BSA were stained with the prepared solution of Coomassie Brilliant Blue G-250 and the absorbance of PN was measured by UV at 595 nm after standing for 2.0 min. Polysaccharides (PS) contents were analyzed using the anthrone method57. Because PS can react with anthrone to a blue-green solution. EPS and prepared glucose standard solutions can be heated and reacted with anthrone and the absorbance measured by UV at 620 nm.

Three-dimensional excitation emission matrix (3D-EEM) spectra were measured by a F-7000 fluorescence spectrophotometer (Hitachi, Japan). The specific experimental conditions are as follows: The wavelength of the emitted light ranges from 250 to 550 nm at 1 nm increment and the wavelength range of the excitation light is from 200 to 450 nm in an increment of 5 nm. The scanning speed is 2400 nm/min and the emission and excitation slit bandwidths are 5 nm38.

Correlation analysis was carried out though Pearson correlation coefficient calculation module of IBM SPSS Statistics version 22.0 which was mainly used to quantify the correlation between FCMC or SRF values and different fractions in sludge EPS58.

The datasets used and/or analysed during the current study available from the corresponding author on reasonable request.

Wu, B., Dai, X. H. & Chai, X. L. Critical review on dewatering of sewage sludge: Influential mechanism, conditioning technologies and implications to sludge re-utilizations. Water Res. 180, 115912 (2020).

Liu, Y. Z. et al. Synthesis of novel chitosan-based flocculants with amphiphilic structure and its application in sludge dewatering: Role of hydrophobic groups. J. Clean. Prod. 249, 119350 (2020).

Kamizela, T. & Kowalczyk, M. Sludge dewatering: Processes for enhanced performance. In Industrial and Municipal Sludge (eds Kamizela, T. & Kowalczyk, M.) 399–423 (Elsevier, 2019).

Liang, J. L. et al. Evaluation of the dewaterability, heavy metal toxicity and phytotoxicity of sewage sludge in different advanced oxidation processes. J. Clean. Prod. 265, 121839 (2020).

Luo, H. J., Ning, X. A., Liang, X. J., Feng, Y. F. & Liu, J. Y. Effects of sawdust-CPAM on textile dyeing sludge dewaterability and filter cake properties. Biores. Technol. 139, 330–336 (2013).

Wei, H., Gao, B. Q., Ren, J., Li, A. M. & Yang, H. Coagulation/flocculation in dewatering of sludge: A review. Water Res. 143, 608–631 (2018).

Hu, P., Zhuang, S. H., Shen, S. H., Yang, Y. H. & Yang, H. Dewaterability of sewage sludge conditioned with a graft cationic starch-based flocculant: Role of structural characteristics of flocculant. Water Res. 189, 116578 (2021).

Houghton, J., Quarmby, J. & Stephenson, T. Municipal wastewater sludge dewaterability and the presence of microbial extracellular polymer. Water Sci. Technol. 44, 373–379 (2001).

Neyens, E., Baeyens, J. & Dewil, R. Advanced sludge treatment affects extracellular polymeric substances to improve activated sludge dewatering. J. Hazard. Mater. 106, 83–92 (2004).

Guan, Q. G. et al. Advances on sludge properties and dewaterability with chemical conditioning. Asian J. Chem. 26(8), 2199–2203 (2014).

Wu, Y. et al. Combined sludge conditioning of micro-disintegration, floc reconstruction and skeleton building (KMnO4/FeCl3/Biochar) for enhancement of waste activated sludge dewaterability. J. Taiwan Inst. Chem. Eng. 74, 121–128 (2017).

Wei, H., Tang, Y. N., Li, A. M. & Yang, H. Insights into the effects of acidification on sewage sludge dewaterability through pH repeated adjustment. Chemosphere 227, 269–276 (2019).

Wei, H., Tang, Y. N., Shoeib, T., Li, A. M. & Yang, H. Evaluating the effects of the preoxidation of H2O2, NaClO, and KMnO4 and reflocculation on the dewaterability of sewage sludge. Chemosphere 234, 942–952 (2019).

Liang, J. L. et al. A highly efficient conditioning process to improve sludge dewaterability by combining calcium hypochlorite oxidation, ferric coagulant re-flocculation, and walnut shell skeleton construction. Chem. Eng. J. 361, 1462–1478 (2019).

Alvarenga , E. , Hayrapetyan , S. , Govasmark , E. , Hayrapetyan , L. & Salbu , B. Study of the flocculation of anaerobically digested residue and filtration properties of bentonite based mineral conditioners .J. Environment.Chem.Eng.3, 1399–1407 (2015).

Liu, H. et al. Conditioning of sewage sludge by Fenton’s reagent combined with skeleton builders. Chemosphere 88, 235–239 (2012).

Masihi, H. & Gholikandi, G. B. Using thermal-acidic-modified kaolin as a physical-chemical conditioner for waste activated sludge dewatering. Chem. Eng. J. 412, 128664 (2021).

BeMiller, J. N. & Whistler, R. L. Starch: Chemistry and Technology 3rd edn. (Academic Press, 2009).

Wei, H., Ren, J., Li, A. M. & Yang, H. Sludge dewaterability of a starch-based flocculant and its combined usage with ferric chloride. Chem. Eng. J. 349, 737–747 (2018).

Huang, P. & Ye, L. Enhanced dewatering of waste sludge with polyacrylamide/montmorillonite composite and its conditioning mechanism. J. Macromol. Sci. Part B 53(9), 1465–1476 (2014).

Huang, R. L. et al. Removal of Cd(II) and Pb(II) from aqueous solution by modified attapulgite clay. Arab. J. Chem. 13(4), 4994–5008 (2020).

Luo, Q., Liu, W. L., Zhuo, Q. M. & Han, Y. H. Interaction mechanism of organic carboxylate with kaolinite and montmorillonite: A density functional theory study. Colloids Surf. A 613, 126047 (2021).

Ye, C. Q. et al. Alkalinity effect of coagulation with polyaluminum chlorides: Role of electrostatic patch. Colloids Surf. A 294(1–3), 163–173 (2007).

Zhang, W. J. et al. Understanding the impact of chemical conditioning with inorganic polymer flocculants on soluble extracellular polymeric substances in relation to the sludge dewaterability. Sep. Purif. Technol. 132, 430–437 (2014).

Hu, Y. Q. et al. Dye adsorption by resins: Effect of ionic strength on hydrophobic and electrostatic interactions. Chem. Eng. J. 228, 392–397 (2013).

Zavala, M. A. L. & Patlan, J. I. R. Enhancement of activated sludge dewaterability by using filamentous fungi as bioadditives. Water 8(11), 531–542 (2016).

Chen, Z., Zhang, W. J., Wang, D. S., Ma, T. & Bai, R. Y. Enhancement of activated sludge dewatering performance by combined composite enzymatic lysis and chemical re-flocculation with inorganic coagulants: Kinetics of enzymatic reaction and re-flocculation morphology. Water Res. 83, 367–376 (2015).

Xue, Q. & Chen, Y. J. Experimental study on municipal sludge dewatering capacity by using quicklime and slag. Desalin. Water Treat. 54(6), 1499–1506 (2015).

Wu, H., Liu, Z. Z., Yang, H. & Li, A. M. Evaluation of chain architectures and charge properties of various starch-baesedflocculants forflocculation of humic acid from water. Water Res. 96, 126–135 (2016).

Wang, S., Yang, Y. K., Chen, X. G., Lv, J. Z. & Li, J. Effects of bamboo powder and rice husk powder conditioners on sludge dewatering and filtrate quality. Int. Biodeterior. Biodegrad. 124, 288–296 (2017).

Zhang, W. J. et al. Improvement of wastewater sludge dewatering performance using titanium salt coagulants (TSCs) in combination with magnetic nano-particles: Significance of titanium speciation. Water Res. 110, 102–111 (2017).

Qi, Y., Thapa, K. B. & Hoadley, A. F. A. Application of filtration aids for improving sludge dewatering properties—A review. Chem. Eng. J. 171(2), 373–384 (2011).

Li, X. Y. & Yang, S. F. Influence of loosely bound extracellular polymeric substances (EPS) on the flocculation, sedimentation and dewaterability of activated sludge. Water Res. 41(5), 1022–1030 (2007).

Mahata, C., Dhar, S., Ray, S. & Das, D. Flocculation characteristics of anaerobic sludge driven-extracellular polymeric substance (EPS) extracted by different methods on microalgae harvesting for lipid utilization. Biochem. Eng. J. 167, 107898 (2021).

Chetry, N., Devi, T. G. & Karlo, T. Synthesis and characterization of metal complex amino acid using spectroscopic methods and theoretical calculation. J. Mol. Struct. 1250, 131670 (2022).

Kumar, D. & Rub, M. A. Influence of dicationic quaternary ammonium gemini surfactant system on metal-amino acid complex-ninhydrin reaction. Mater. Chem. Phys. 248, 122926 (2020).

Anjum, M., Al-Makishah, N. H. & Barakat, M. A. Wastewater sludge stabilization using pre-treatment methods. Process Saf. Environ. Prot. 102, 615–632 (2016).

Sheng, G. P., Yu, H. Q. & Li, X. Y. Extracellular polymeric substances (EPS) of microbial aggregates in biological wastewater treatment systems: A review. Biotechnol. Adv. 28(6), 882–894 (2020).

Zhang, W., Dai, X. H., Dong, B. & Dai, L. L. New insights into the effect of sludge proteins on the hydrophilic/hydrophobic properties that improve sludge dewaterability during anaerobic digestion. Water Res. 173, 115503 (2020).

Wang, W. Y. et al. Effect of SDS and neutral protease on the release of extracellular polymeric substances (EPS) from mechanical dewatered sludge. Waste Biomass Valoriz. 10(4), 1053–1064 (2017).

Gao, J. L., Weng, W., Yan, Y. X., Wang, Y. C. & Wang, Q. K. Comparison of protein extraction methods from excess activated sludge. Chemosphere 249, 126107 (2020).

Chen, W., Westerhoff, P., Leenheer, J. A. & Booksh, K. Fluorescence excitation-emission matrix regional integration to quantify spectra for dissolved organic matter. Chem. Biochem. 37(24), 5701–5710 (2003).

Jacquin, C., Lesage, G., Traber, J., Pronk, W. & Heran, M. Three-dimensional excitation and emission matrix fluorescence (3DEEM) for quick and pseudo-quantitative determination of protein- and humic-like substances in full-scale membrane bioreactor (MBR). Water Res. 118, 82–92 (2017).

Li, Y. F. et al. Enhancing the sludge dewaterability by electrolysis/electrocoagulation combined with zero-valent iron activated persulfate process. Chem. Eng. J. 303, 636–645 (2016).

Tuan, P. A. & Sillanpää, M. Effect of freeze/thaw conditions, polyelectrolyte addition, and sludge loading on sludge electro-dewatering process. Chem. Eng. J. 164(1), 85–91 (2010).

Xu, Q. Y. et al. Highly effective enhancement of waste activated sludge dewaterability by altering proteins properties using methanol solution coupled with inorganic coagulants. Water Res. 138, 181–191 (2018).

Cao, B. D. et al. Wastewater sludge dewaterability enhancement using hydroxyl aluminum conditioning: Role of aluminum speciation. Water Res. 105, 615–624 (2016).

Zhu, Y. W. et al. Profiling of amino acids and their interactions with proteinaceous compounds for sewage sludge dewatering by Fenton oxidation treatment. Water Res. 175, 115645 (2020).

Liu, Z. Z., Huang, M., Li, A. M. & Yang, H. Flocculation and antimicrobial properties of a cationized starch. Water Res. 119, 57–66 (2017).

APHA. Standard Methods for the Examination of Water and Wastewater 20th edn. (American Public Health Association, 1998).

Liu, J. et al. Effective improvement of activated sludge dewaterability conditioning with seawater and brine. Chem. Eng. J. 168(3), 1112–1119 (2011).

Guo, J. Y., Jiang, S. L. & Pang, Y. J. Rice straw biochar modified by aluminum chloride enhances the dewatering of the sludge from municipal sewage treatment plant. Sci. Total Environ. 654, 338–344 (2019).

Wójcik, M. Investigation of filtration properties and microbiological characteristics of sewage sludge after physical conditioning with the use of ground walnut shells. Powder Technol. 361, 491–498 (2020).

Niu, M. Q., Zhang, W. J., Wang, D. S., Chen, Y. & Chen, R. L. Correlation of physicochemical properties and sludge dewaterability under chemical conditioning using inorganic coagulants. Biores. Technol. 144, 337–343 (2013).

Bradford, M. M. A rapid and sensitive method for the quantitation of microgram quantities of protein utilizing the principle of protein-dye binding. Anal. Biochem. 72(1–2), 248–254 (1976).

Kim, M. S. et al. Disintegration of waste activated sludge by thermally-activated persulfates for enhanced dewaterability. Environ. Sci. Technol. 50(13), 7106–7115 (2016).

Frolund, B., Palmgren, R., Keiding, K. & Nielsen, P. H. Extraction of extracellular polymers from activated sludge using a cation exchange resin. Water Res. 30(8), 1749–1758 (1996).

Guo, Z. Y. et al. Dewatering performance of sewage sludge under pretreatment with modified corn-core powder. Sci. Total Environ. 684, 402–412 (2019).

This study was supported by the National Natural Science Foundation of China (grant no. 51978325).

State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing, 210023, People’s Republic of China

Shaohang Shen, Yu Pan, Pan Hu & Hu Yang

School of Ecology Technology and Engineering, Shanghai Institute of Technology, Shanghai, 201418, People’s Republic of China

You can also search for this author in PubMed  Google Scholar

You can also search for this author in PubMed  Google Scholar

You can also search for this author in PubMed  Google Scholar

You can also search for this author in PubMed  Google Scholar

You can also search for this author in PubMed  Google Scholar

S.H.S. performed these experiments, analyzed the results and wrote the manuscript. H.W., P.H. and Y.P. performed these experiments and wrote the manuscript. H.Y. is the corresponding author (Tel & Fax: 86-25-89681272, E-mail: yanghu@nju.edu.cn), designed the experiments, reviewed and edited the manuscript. All the authors read and approved the manuscript.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Shen, S., Wei, H., Pan, Y. et al. The enhanced dewaterability of sludge by a starch-based flocculant combined with attapulgite. Sci Rep 13, 402 (2023). https://doi.org/10.1038/s41598-023-27749-3

DOI: https://doi.org/10.1038/s41598-023-27749-3

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.

Scientific Reports (Sci Rep) ISSN 2045-2322 (online)

The enhanced dewaterability of sludge by a starch-based flocculant combined with attapulgite | Scientific Reports

Paper Chemical Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.